Recent Content by lokey

  1. lokey
    Post

    650-701 Build

    here's a 6m6 exhaust manifold with a 61x gasket, the left side shows how much smaller the ports are [img]
    Post by: lokey, July 16, 2009 in forum: Tech Discussion
  2. lokey
    Post

    Alloy pump duct for a blaster

    I broke the duct on my blaster just before xmas, got Roger to bring over a Jet Dynamics alloy duct, took a little bit of grinding to make it fit...
    Post by: lokey, February 20, 2009 in forum: For Sale & Wanted
  3. lokey
    Post

    701 pistons wanted

    I've got a set of .75mm over prox pistons and rings, pulled after about 10-12hrs due to cracked cylinder, cost me 400 in jan 08 - open to offers
    Post by: lokey, February 4, 2009 in forum: For Sale & Wanted
  4. lokey
    Post

    lokey's blaster

    thanks wax :) I've got a commercial tiny tach on its way so i'll wait until that arrives before playing with the screws, it'll be good to have some...
    Post by: lokey, February 25, 2008 in forum: User's Rides and Builds
  5. lokey
    Post

    lokey's blaster

    3/4 out on top, middle and bottom closed pipe doesnt seem all that hot so could probably be closed up some more? I am wary of flywheel lightening...
    Post by: lokey, February 25, 2008 in forum: User's Rides and Builds
  6. lokey
    Post

    lokey's blaster

    The cases havent been touched, i'm pretty stoked with the power at the moment it hits hard in the midrange but could do with a little more punch down...
    Post by: lokey, February 25, 2008 in forum: User's Rides and Builds
  7. lokey
    Post

    lokey's blaster

    maybe :wink: [img] [img]
    Post by: lokey, February 25, 2008 in forum: User's Rides and Builds
  8. lokey
    Post

    lokey's blaster

    Thanks :) The rear piston and head dome had some nasty pitting from detonation so i assume it was just too lean, not sure whether it was tuning on...
    Post by: lokey, February 25, 2008 in forum: User's Rides and Builds
  9. lokey
    Thread

    lokey's blaster

    I bought this from trademe a couple of weeks before xmas to replace my 93 blaster, it looked like a minter with factory pipe and 'recently rebuilt...
    Thread by: lokey, February 24, 2008, 12 replies, in forum: User's Rides and Builds
  10. lokey
    Post

    Can Anyone help?

    ok, a bit tricky getting verniers in there but it looks like 87mm to the bottom and 85mm to the top
    Post by: lokey, February 7, 2008 in forum: Tech Discussion
  11. lokey
    Post

    Can Anyone help?

    Hey, i've got my timing cover and stator off at the moment but its a bit too tight on space for getting good readings, i took some quick photos one...
    Post by: lokey, February 7, 2008 in forum: Tech Discussion
  12. lokey
    Post

    Porting

    Cheers Tim, I have talked to Roger and he confirmed pretty much what you said. Heres the link for the Sport Porting thread on PWCToday for anyone...
    Post by: lokey, January 3, 2008 in forum: Tech Discussion
  13. lokey
    Post

    Porting

    thanks Rick, will do Just curious, is it normal for stock ports to be this badly matched? [img]
    Post by: lokey, January 3, 2008 in forum: Tech Discussion
  14. lokey
    Thread

    Porting

    I'm in the process of getting my 701 engine rebuilt and noticed the sleeve/cylinder ports are mismatched really bad, is there anyone in NZ with...
    Thread by: lokey, January 3, 2008, 50 replies, in forum: Tech Discussion